--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -10,6 +10,8 @@
 #include <dt-bindings/reset/qcom,gcc-ipq806x.h>
 #include <dt-bindings/soc/qcom,gsbi.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
 
 / {
 	#address-cells = <1>;
@@ -30,6 +32,16 @@
 			next-level-cache = <&L2>;
 			qcom,acc = <&acc0>;
 			qcom,saw = <&saw0>;
+			clocks = <&kraitcc 0>, <&kraitcc 4>;
+			clock-names = "cpu", "l2";
+			clock-latency = <100000>;
+			cpu-supply = <&smb208_s2a>;
+			operating-points-v2 = <&opp_table0>;
+			voltage-tolerance = <5>;
+			cooling-min-state = <0>;
+			cooling-max-state = <10>;
+			#cooling-cells = <2>;
+			cpu-idle-states = <&CPU_SPC>;
 		};
 
 		cpu1: cpu@1 {
@@ -40,11 +52,125 @@
 			next-level-cache = <&L2>;
 			qcom,acc = <&acc1>;
 			qcom,saw = <&saw1>;
+			clocks = <&kraitcc 1>, <&kraitcc 4>;
+			clock-names = "cpu", "l2";
+			clock-latency = <100000>;
+			cpu-supply = <&smb208_s2b>;
+			operating-points-v2 = <&opp_table0>;
+			voltage-tolerance = <5>;
+			cooling-min-state = <0>;
+			cooling-max-state = <10>;
+			#cooling-cells = <2>;
+			cpu-idle-states = <&CPU_SPC>;
+ 		};
+
+		idle-states {
+			CPU_SPC: spc {
+				compatible = "qcom,idle-state-spc";
+				status = "disabled";
+				entry-latency-us = <400>;
+				exit-latency-us = <900>;
+				min-residency-us = <3000>;
+			};
 		};
+	};
 
-		L2: l2-cache {
-			compatible = "cache";
-			cache-level = <2>;
+	opp_table_l2: opp_table_l2 {
+		compatible = "operating-points-v2";
+
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <100000>;
+			opp-level = <0>;
+		};
+
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <100000>;
+			opp-level = <1>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1150000>;
+			clock-latency-ns = <100000>;
+			opp-level = <2>;
+		};
+	};
+
+	opp_table0: opp_table0 {
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
+
+		/*
+		 * Voltage thresholds are <target min max>
+		 */
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>;
+			opp-microvolt-speed0-pvs1-v0 = <925000 878750 971250>;
+			opp-microvolt-speed0-pvs2-v0 = <875000 831250 918750>;
+			opp-microvolt-speed0-pvs3-v0 = <800000 760000 840000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+			opp-level = <0>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>;
+			opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>;
+			opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>;
+			opp-microvolt-speed0-pvs3-v0 = <850000 807500 892500>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+			opp-level = <1>;
+		};
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>;
+			opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>;
+			opp-microvolt-speed0-pvs2-v0 = <995000 945250 1044750>;
+			opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+			opp-level = <1>;
+		};
+
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>;
+			opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>;
+			opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>;
+			opp-microvolt-speed0-pvs3-v0 = <950000 902500 997500>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+			opp-level = <1>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1200000 1140000 1260000>;
+			opp-microvolt-speed0-pvs1-v0 = <1125000 1068750 1181250>;
+			opp-microvolt-speed0-pvs2-v0 = <1075000 1021250 1128750>;
+			opp-microvolt-speed0-pvs3-v0 = <1000000 950000 1050000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+			opp-level = <2>;
+		};
+
+		opp-1400000000 {
+			opp-hz = /bits/ 64 <1400000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1250000 1187500 1312500>;
+			opp-microvolt-speed0-pvs1-v0 = <1175000 1116250 1233750>;
+			opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>;
+			opp-microvolt-speed0-pvs3-v0 = <1050000 997500 1102500>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+			opp-level = <2>;
 		};
 	};
 
@@ -317,6 +443,15 @@
 		};
 	};
 
+	fab-scaling {
+		compatible = "qcom,fab-scaling";
+		clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>;
+		clock-names = "apps-fab-clk", "ddr-fab-clk";
+		fab_freq_high = <533000000>;
+		fab_freq_nominal = <400000000>;
+		cpu_freq_threshold = <1000000000>;
+	};
+
 	firmware {
 		scm {
 			compatible = "qcom,scm-ipq806x", "qcom,scm";
@@ -384,6 +519,15 @@
 				};
 			};
 
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
 			spi_pins: spi_pins {
 				mux {
 					pins = "gpio18", "gpio19", "gpio21";
@@ -437,6 +581,27 @@
 					bias-bus-hold;
 				};
 			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "mdio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29",
+					       "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59",
+					       "gpio60", "gpio61", "gpio62";
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
 		};
 
 		intc: interrupt-controller@2000000 {
@@ -513,6 +678,17 @@
 			regulator;
 		};
 
+		saw_l2: regulator@02012000 {
+			compatible = "qcom,saw2", "syscon";
+			reg = <0x02012000 0x1000>;
+			regulator;
+		};
+
+		sic_non_secure: sic-non-secure@12100000 {
+			compatible = "syscon";
+			reg = <0x12100000 0x10000>;
+		};
+
 		gsbi2: gsbi@12480000 {
 			compatible = "qcom,gsbi-v1.0.0";
 			cell-index = <2>;
@@ -637,6 +813,33 @@
 			};
 		};
 
+		gsbi6: gsbi@16500000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <6>;
+			reg = <0x16500000 0x100>;
+			clocks = <&gcc GSBI6_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi6_i2c: i2c@16580000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		gsbi7: gsbi@16600000 {
 			status = "disabled";
 			compatible = "qcom,gsbi-v1.0.0";
@@ -658,6 +861,19 @@
 				clock-names = "core", "iface";
 				status = "disabled";
 			};
+
+			gsbi7_i2c: i2c@16680000 {
+ 				compatible = "qcom,i2c-qup-v1.1.1";
+ 				reg = <0x16680000 0x1000>;
+				interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+
+ 				clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>;
+ 				clock-names = "core", "iface";
+				status = "disabled";
+
+ 				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 		};
 
 		rng@1a500000 {
@@ -761,6 +977,17 @@
 			};
 		};
 
+		L2: l2-cache {
+			compatible = "qcom,krait-cache", "cache";
+			cache-level = <2>;
+			qcom,saw = <&saw_l2>;
+
+			clocks = <&kraitcc 4>;
+			clock-names = "l2";
+			l2-supply = <&smb208_s1a>;
+			operating-points-v2 = <&opp_table_l2>;
+		};
+
 		rpm: rpm@108000 {
 			compatible = "qcom,rpm-ipq8064";
 			reg = <0x108000 0x1000>;
@@ -828,6 +1055,11 @@
 			clock-output-names = "acpu_l2_aux";
 		};
 
+		kraitcc: clock-controller {
+			compatible = "qcom,krait-cc-v1";
+			#clock-cells = <1>;
+		};
+
 		lcc: clock-controller@28000000 {
 			compatible = "qcom,lcc-ipq8064";
 			reg = <0x28000000 0x1000>;
@@ -835,6 +1067,11 @@
 			#reset-cells = <1>;
 		};
 
+		sfpb_mutex_block: syscon@1200600 {
+			compatible = "syscon";
+			reg = <0x01200600 0x100>;
+		};
+
 		pcie0: pci@1b500000 {
 			compatible = "qcom,pcie-ipq8064";
 			reg = <0x1b500000 0x1000
@@ -1184,6 +1421,21 @@
 			};
 		};
 
+
+		mdio0: mdio@37000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			compatible = "qcom,ipq8064-mdio", "syscon";
+			reg = <0x37000000 0x200000>;
+			resets = <&gcc GMAC_CORE1_RESET>;
+			reset-names = "stmmaceth";
+			clocks = <&gcc GMAC_CORE1_CLK>;
+			clock-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
 		vsdcc_fixed: vsdcc-regulator {
 			compatible = "regulator-fixed";
 			regulator-name = "SDCC Power";
@@ -1258,4 +1510,17 @@
 			};
 		};
 	};
+
+	sfpb_mutex: sfpb-mutex {
+		compatible = "qcom,sfpb-mutex";
+		syscon = <&sfpb_mutex_block 4 4>;
+
+		#hwlock-cells = <1>;
+	};
+
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem>;
+		hwlocks = <&sfpb_mutex 3>;
+	};
 };
